Menu Close

Can you put a 350 in a 4×4 S10?

Can you put a 350 in a 4×4 S10?

I would go with a tbi or Vortec 350 personally just for the ease of the swap. You can keep your A/C and 4wd, but you will need a special oil pan to clear the diff and your cooling system will need done correctly to handle the heat with the a/c. As far as cost goes, that’s wide open.

How many cubic inches is a 4.3-liter engine?

262 cu in
The 4.3 L (262 cu in) V6 has a 4 in × 3.48 in (101.6 mm × 88.4 mm) bore and stroke, identical to the 350 cu in (5.7 L) Chevrolet V8 engine.

Will a 305 fit an S10?

Transmission should be fine. A 305 will bolt right up to a 4.3’s tranny, and will survive with no issues as long as your hp output stays below 350 or so.

Is the Chevy S10 Reliable?

It has been the most reliable truck I’ve ever owned. I purchased this truck as a commuter vehicle to keep the miles off of my Chevy Diesel. So far my Chevy S10 has over 250,000 miles on it, and it’s still going strong. The only complaint is about the door hinge pins, which are notorious for wearing out.

What does S10 stand for?

S10

Acronym Definition
S10 Sabine 10-Bit Text System (file extension)

How much does it cost to V8 swap a S10?

The average cost we’ve found, for a V-8 conversion and all of the parts necessary is between $3,500-7,500.

Can you put a V8 in a S10 Blazer?

RE: V8 in s10 blazer Your trans will bolt up to the v8. You will need to find the appropriate 4 or 5 speed trans to fit in there and you still may have to find the appropriate driveshafts to work with it if the lengths are different.

Is a 5.3 a V6 or V8?

Available with AFM and DFM, the 5.3L EcoTec3 V8 engine offers lasting and reliable performance. Expect up to 17 city and 24 highway MPG, as well as 355 HP and 383 lb. -ft. of torque.

How long will a Chevy S10 last?

ford and chevy have better clutch brand in it… u see what i am trying to say but yes S10 do usually run long until between usually 180k to 280k is a very usually for all chevrolet.. rare to hit 300k or more…

What kind of engine does a Chevy S10 have?

The Chevy 350 engine works extremely well in the S10 and GMC S15 chassis; if nothing else, even a bone-stock 350 is a sure 25 boost in horsepower and torque over the already fairly stout 4.3-liter V-6 engine. For many, this — combined with a V-8 exhaust note and tire-shredding capability at will — will be enough.

What are the dimensions of a Chevy S-10?

Visit Chevrolet for more information on the Chevrolet S-10. All dimensions are in inches unless otherwise noted.

Can you put a 350 engine in a S10?

TBI engines with 700-R4, 4L60 or T-5 transmissions work best for this swap. You may need to get a high-mount alternator bracket to clear the steering components. Physically getting a 350 engine into an S10 chassis may be the simplest part of the entire swap.

Is the small block S10 a hot rod?

Imports and former mom-mobiles with shiny rims might be cute, but a small-block S-10 is a hot-rod. In fact, some might say it’s the last hot-rod, the ultimate incarnation of the old-school recipe for going fast: a big V-8 swap into a simple, lightweight, full-frame chassis.