Table of Contents
Where is the computer module on a 2003 Ford Explorer Sport Trac?
It is located on the passenger side of the engine compartment.
Where is the computer module on a 2002 Ford Explorer Sport Trac?
It is below the seat belt mechanism. You have to pull out the top plastic panel off, then loosen the lower panel to be able to see the face of the computer module. The code is on a sticker on the face of the module.
Where is the computer module located on a 2005 Ford Explorer Sport Trac?
The sticker should still be on teh module, and according to the service manual, the module is located behind the passenger side air bag.
Why did they stop making Ford Explorer Sport Trac?
The Sport Trac was discontinued in 2010 when high fuel prices and the recession saw demand drop off considerably. Had Ford continued to develop the Explorer Sport Trac, it probably wouldn’t have needed to revive the Ranger.
Where is the PCM located on a 2004 Ford Explorer?
The PCM is located in the rear of the Engine compartment on the passanger side.
How do you reset the door code on a Ford Explorer Sport Trac?
From the vehicle list menu, select Door Keypad Code. Enter your factory key code that can be found in the owner’s manual. Enter your new personal key code. After you have entered in your factory code, wait for the prompt and enter in a new 5-digit key code of your choosing.
How do you reset the keyless entry on a 2004 Ford Explorer?
2004 Ford Explorer Keyless Entry Remote Fob Programming Instructions
- Close all doors and then open drivers door and press the UNLOCK button on drivers door panel while door is open and insert key in ignition.
- Turn ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in RUN.
How many miles will a Ford Explorer Sport Trac last?
According to Motor and Wheels, “A Ford Explorer can last up to 10-17 years with regular maintenance. An average Ford Explorer can easily achieve 80,000 to 200,000 miles.
Is the Ford Explorer Sport Trac a good truck?
Ford Explorer Sport Trac Ratings Overview The average rating is a 4 out of 5 stars. The Ford Explorer Sport Trac Reliability Rating is 3.5 out of 5. It ranks 21st out of 32 for all car brands. Learn more about Ford Explorer Sport Trac Reliability Ratings.
How do you reset a PCM Ford Explorer?
How do you reset a PCM Ford Explorer?
- Open the hood of the Ford. Loosen the lock nut located on the negative battery cable connector with a socket and ratchet.
- Wait for 20 minutes while the PCM bleeds off the electricity it stores for backup power. Once the power drains from the PCM, it resets.
What is PCM on Ford Explorer?
It uses a large network of sensors, solenoids, sending units, and other electronic components to both receive and send information which enables the vehicle to run at peak performance. The PCM also allows for inputs from other systems on the vehicle, and may have the ability to control the transmission as well.
How do you repair an overhead compass in a Ford Explorer?
Pulling down on the tab will begin to release the console from the ceiling. Slide your fingers into the gap until you are 3/4 of the way toward the front. Next, pull the console firmly to release the two tabs that secure it to the ceiling. 2001 Ford Explorer Sportrac Overhead Console.
What kind of compass does Ford Explorer sportrac have?
2001 Ford Explorer Sportrac at Corolla, NC. Described by Car & Driver as the Swiss army knife of SUVs. Yet, age and heat degrade electric components needing repair. For several months, the digital compass and temperature display gradually faded.
How to fix Ford overhead console display-temperature?
The Automotive Enthusiast Channel. Weekly Videos!!! Content: Drag Racing, Car Shows, Vehicle Repairs, How To’s, Aftermarket Install’s & So Much More! About Me: Southwest Florida, Father Of Two, Car Guy.
What is the Ford Explorer sportrac overhead console?
2001 Ford Explorer Sportrac Overhead Console. At this point, the console will be dangling by the main electrical harness and the sun-roof motor plug. Disconnecting these plugs is simple, but not necessarily easy depending on your patience, dexterity and tools available.